PCL-18B-2 HV/36000lb/MobileLift/Setof2 – HIGH VOLTAGE (460/360V) This PCL-18B mobile column lift system comes in a set of 2. When combined, the system lifts up to 36,000 lbs. A set of 2 is the perfect way to expand your lifting capabilities on vehicles with three or four axles. Sets of 4, 6 and 8 are available.
With a pair (2) of mobile column lifts, you can add to your existing fleet and expand your lifting capabilities to include larger semi-trucks and heavy-duty vehicles. A minimum of 4 mobile column lifts must be used to lift a vehicle, and heavier vehicles require 6 or 8. This 2-set is a great way to gradually upgrade into the 6 or 8-lift range, offering up to 144,000 lbs. with a full set.
Do not attempt to lift half of a vehicle (the front or back only) with only 2 mobile lifts. Vehicles must be raised on an even plane at all times.

Specification:

• HIGH VOLTAGE UNITS

• 18,000-lb. individual column capacity / 108,000-lb. maximum system capacity

• Meets or exceeds the standards prescribed by ANSI/ALI ALCTV-2011

• Two, four, or six column configurations can accommodate heavy duty trucks and light duty passenger vehicles

• 208-240V, 3-phase main power system - optional voltages available upon request

• SINGLE, PAIR or TEAM operation

• For a standard four-column set, just three 30' cables are used leaving the front or back of the lift clear of cable obstructions

• Simple operation, long service life and minimum maintenance

• Intuitive controls allow the lift to be fully programmed and controlled from any column

• Control systems feature 24-volt safety circuitry

• The PLC and main system components are standard off-the-shelf brands rather than proprietary printed circuit boards or controls, which can be very expensive to service or replace

• Smart electronics feature self-diagnostics and self-calibration functions

• Sealed and enclosed linear potentiometers feature precision potentiometric output and high-frequency response for precise synchronization and communication of all columns throughout all operation cycles for precise, level lifting

• Variable height limit settings can be programmed for shops with low ceilings or when specific vehicle service requirements necessitate specific rise heights

• Two-speed lowering option – turtle or rabbit speed settings

• Each column is equipped with a warning light and audible alarm for critical warning alerts

• Emergency shut-off switches on each column quickly shut off power to the lift in the event an unsafe condition is detected by the operator

• Separate key lock enclosure on each column

• Electronics are multi-fuse protected

• An enclosed electric-hydraulic power system that ensures quieter operation is better suited for sound-sensitive areas

• Pallet-jack style steering wheels enable the columns to be lowered firmly on the floor vs. constantly loaded spring-type steering wheels that can cause columns to roll when unladen by the weight of a vehicle

• Low-mounted power units and cylinders means a lower center of gravity, making the columns easier to move and less likely to topple vs. screw-drive systems with heavy overhead motors and drive systems

• Extended forks accommodate wide tires and deep wheel configurations

• Multi-width wheel forks with locking pins accommodate the widest range of wheels, eliminating the need for specialty wheel adapters

• Tandem 8” diameter polyurethane covered steel wheels with sealed roller bearings easily roll over dirt and debris

• Heavy-duty steel carriage rollers feature turned, ground and polished axle pins

• Manual safety override valves on each column permit the lift to be lowered in the event of a power outage without the need for manual hand cranks

• Durable forklift pockets provide simplistic handling when moving the lift columns from one facility to another

• Inverted hydraulic cylinders feature an integrated safety valve to prevent accidental uncontrolled lowering in the event of oil pressure loss

• Multiple, automatic, independent safety locks spaced every four inches ensure safe operation

• Space-saving design, reduced column weight and a tight turning radius provides improved mobility

• Use the lift to place vehicles on tall jack stands then use the columns to raise another vehicle in an adjoining bay

• Durable powder coat finish

BENDPAK NUMBER #5175295
For warranty information, shipping, and FAQ, please visit: BendPak info page